manualshive.com logo in svg

Komatsu D51EX-24, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu D51EX-24 Скачать руководство пользователя страница 195

METHOD FOR HEATING SEAT

Turn on the seat heater switch.
(a): OFF position
(b): ON position
The backrest and seat surface are heated.

When the seat heater switch is turned on, the heater in the seat operates. When the seat surface temperature
exceeds approximately 20 °C, the heater is turned off automatically. When the temperature decreases below ap-
proximately 10 °C, the heater is turned on automatically.

REMARK

When  the  seat  surface  temperature  is  above  approximately  20 °C,  the  heater  does  not  operate  even  if  the
switch is turned on.

MECHANICAL SUSPENSION SEAT

(if equipped)

METHOD FOR ADJUSTING SEAT IN FORE-AND-AFT DIRECTION

1.

Pull  up  the  fore-aft  adjustment  lever,  and  set  the  seat  to
the desired position.
Fore-and-aft adjustment range: 180 mm (18 steps)

2.

After adjusting, release the lever.

METHOD FOR RECLINING SEAT

The reclining of the seat becomes large when the seat is moved forward, and it becomes smaller as the seat is
moved backward. When moving the seat backward, return the reclined seat back to the original position.

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-139

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды