Komatsu D51EX-24 Скачать руководство пользователя страница 301 | Manualshive

Страница: 301 / 382

Komatsu D51EX-24 Скачать руководство пользователя страница 301

METHOD FOR ADJUSTING

k

k

WARNING

Never loosen plug (1) more than 1 turn.
If plug (1) is loosened more than 1 turn, there is a danger
of plug (1) flying out under the high internal pressure of
the grease.
Never loosen any part other than plug (1). Never put your
face in the mounting direction of plug (1).
If the track tension cannot be loosened by the above pro-
cedure, ask your Komatsu distributor for repair.

METHOD FOR INCREASING TRACK TENSION

NOTICE

• The safety indicator is stuck to the back of cover (3). Take care not to damage the safety indicator.
• When removing cover (3), be careful not to let any dirt or soil get in.

Prepare a grease pump.
1.

Remove cover (3).

2.

Pump in grease through grease fitting (2) by using a
grease pump.

Grease  can  be  pumped  in  until  dimension  (S)  becomes
zero  (0).  If  the  track  tension  is  still  loose,  the  pins  and
bushings  are  excessively  worn.  The  pins  and  bushings
need to be turned 180 deg. or replaced. Ask your Komatsu
distributor for repair.

3.

Move the machine backward and forward.

4.

Check the belt tension again.
Check that the track tension is proper.
If the track tension is not proper, adjust it again.

METHOD FOR DECREASING TRACK TENSION

k

k

WARNING

It is extremely dangerous to release the grease by any method other than the following procedure.
If track tension is not relieved by this procedure, contact your Komatsu distributor for repairs.

NOTICE

• The safety indicator is stuck to the back of cover (3). Take care not to damage the safety indicator.
• When removing cover (3), be careful not to let any dirt or soil get in.

MAINTENANCE

MAINTENANCE PROCEDURE

4-25

«
...
299
300
301
302
303
...
»

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды