Komatsu D51EX-24 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 382

Komatsu D51EX-24 Скачать руководство пользователя страница 83

FAN REVERSE ROTATION PILOT LAMP

The fan reverse rotation pilot lamp lights up while the fan is ro-
tating in reverse.
For canceling the fan reverse rotation, turn the starting switch
to OFF position and wait for 15 seconds or more, and turn the
starting switch to ON position.

MESSAGE DISPLAY

The User Message is displayed when there is a message from
Komatsu.
To read the message, see “MESSAGE DISPLAY”.
Lights up in green (A): There is unread message.
Lights up in blue (B): There is any read message to which no

reply has been made.

OFF: No messages

OPERATING MODE DISPLAY

The currently set operating mode is displayed on the operating
mode display.
The display of the operating mode is as follows.
(P): For heavy-duty operations
Lights up when the mode is set to power mode.
(E): For operations with emphasis on fuel consumption
Lights up when the mode is set to economy mode.
The operating mode changes each time the operating mode
selector switch is pressed.

ENGINE STOP PILOT LAMP

The engine stop pilot lamp is displayed while the engine is
stopped. It goes out when the engine is started.

OPERATION

EXPLANATION OF COMPONENTS

3-27

«
...
81
82
83
84
85
...
»

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды