manualshive.com logo in svg

Komatsu D51EX-24, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu D51EX-24 Скачать руководство пользователя страница 239

METHOD FOR CHECKING AFTER FINISHING WORK

CHECKS BEFORE STOPPING ENGINE

On  the  machine  monitor,  check  the  engine  coolant  tempera-
ture,  hydraulic  oil  temperature,  engine  oil  pressure,  remaining
fuel level, and remaining DEF level.

CHECKS AFTER STOPPING ENGINE

1.

Perform walk-around check for oil or coolant leakage and for abnormality in work equipment, exterior parts,
and undercarriage.
If oil or coolant leakage or any abnormality is detected, repair it.

2.

Check DEF tank, pump, injector, hose, and joint for leakage.
If any abnormality is found, ask your Komatsu distributor for repair.

3.

Fill the fuel tank.

4.

Check the engine compartment for paper and debris. Clean out any paper and debris to avoid a fire hazard.

5.

Remove any mud affixed to the undercarriage.

LOCK

The following sections are lockable to prevent vandalism.
Places where can be locked with the starting switch key

• Cab door opener (1) (right and left)
• Engine side cover (2) (upper left)
• Engine side cover (3) (lower left)
• Hydraulic tank inspection cover (4)
• DEF tank filler port cover (5)
• Fuel tank inspection cover (6)
• Radiator filler port inspection cover (7)
• Hydraulic tank oil filler cap (8)

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-183

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды