manualshive.com logo in svg

Komatsu D51EX-24, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu D51EX-24 Скачать руководство пользователя страница 253

LOADING AND UNLOADING WITH TRAILER

k

k

 WARNING

• Since loading and unloading of the machine is dangerous, be extremely careful.
• When loading or unloading the machine, lower the engine speed, set the speed range to the 1st, and

operate slowly.

• Use ramps with ample width, length, thickness, and strength and install them with a maximum slope

of 15°.
If the ramps deflect much, reinforce them with blocks, etc.

• Load the machine on a flat and firm ground.

Secure sufficient distance from the road edge.

• Remove mud, etc. from the undercarriage of the machine so that the machine does not slip side-

ways on the ramps.
In addition, remove water, snow, ice, grease, oil, etc. from the ramps.

• Never correct your steering on the ramps. There is danger that the machine may tip over.

If necessary, drive off the ramps or back on to the trailer and correct the direction.

• The center of gravity of the machine shifts suddenly at the joint between the ramps and the trailer,

and it is dangerous that the machine loses its balance. Pass slowly.

 

When loading or unloading the machine, be sure to use ramps or platform, and follow the procedure shown be-
low.

PROCEDURES FOR LOADING MACHINE

Load on a firm and level ground.
1.

Park a trailer on a firm and level ground.
Maintain a safe distance from the road shoulder

2.

Apply the brake of the trailer securely.

3.

Set chocks (1) to the tires to secure the trailer.

4.

Install ramps (2).
Set gap (3) between ramps (2) to match the distance be-
tween  the  right  and  left  tracks,  and  keep  angle  (4)  to  a
maximum of 15 °.
If ramps (2) bend appreciably under the weight of the ma-
chine,  put  wooden  block  (5)  under  the  ramps  to  support
them.

5.

Start the engine.

6.

When transporting the machine with the work equipment installed to it, raise the work equipment.
1) Set  the  work  equipment  lock  lever  to  FREE  position

(F).

2) Operate  the  blade  control  lever  and  raise  the  work

equipment.

OPERATION

TRANSPORTATION

3-197

Содержание D51EX-24































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды