Kohler Courage 3000 Series Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 56

background image

50

Reassembly

KohlerEngines.com

18 690 01 Rev. F

Install Throttle Lever, Governor Lever, Throttle Link, Dampening Spring, and Governor Spring

1. Install nylon washer and wave spring to throttle plate.
2. Connect spring to throttle lever and throttle plate. Install throttle lever to throttle plate. Install tabbed washer (with

tab engaged in slot) and secure with nut.

3.  Torque nut to 5.4 N·m (47.8 in. lb.).
4.  Install governor lever onto shaft.
5.  Connect dampening spring and throttle link to governor lever. Connect governor spring to governor lever and to

throttle lever.

6. Move governor lever clockwise until it stops. Rotate governor shaft clockwise until it stops. Hold both in this

position and torque governor lever nut to 10 N·m (88.5 in. lb.).

«
...
48
49
50
51
52
...
»

Содержание Courage 3000 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для Courage 3000 Series

Бренд: FAZUA Страницы: 76

Бренд: Club Car Страницы: 280

Бренд: CG Страницы: 45

Бренд: MTD Страницы: 40

Бренд: Globe Страницы: 11

Бренд: Man Страницы: 50

Бренд: Motorola Страницы: 82

Бренд: Pacific Страницы: 48

RolloTube S-line DuoFern

Бренд: RADEMACHER Страницы: 8

RolloTube Basis

Бренд: RADEMACHER Страницы: 60

Бренд: RADEMACHER Страницы: 64

CROUZET 801400TNI21

Бренд: Innovista Sensors Страницы: 39

Бренд: YS Страницы: 2

Бренд: Volvo Страницы: 20

Бренд: Volvo Страницы: 51

Бренд: Volvo Страницы: 76

Бренд: YS Страницы: 2

Бренд: Detroit Diesel Страницы: 174

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды