Kohler Courage 3000 Series Скачать руководство пользователя страница 52

Страница: 52 / 56

Reassembly

KohlerEngines.com

18 690 01 Rev. F

Install Oil Sentry

Module

1. Install Oil Sentry

™

module and secure with screw.

2. Connect electrical leads for Oil Sentry

™

module.

Install Fuel Tank

1. Route fuel line across top of engine toward

carburetor while positioning fuel tank on mounting

brackets.

2.  Secure with screw on inner mounting bracket.
3.  Install nuts on fuel tank studs.
4.  Torque fuel tank screw and nuts to 24 N·m

(212 in. lb.).

5. Position fuel line in clip at carburetor and connect

fuel line to shut-oﬀ valve on carburetor. Secure

clamp.

Install Carburetor Cover

Install outer air cleaner cover onto studs and secure with

nuts.

Install Muﬄ

er and Heat Shield Assembly

1. Install a new exhaust gasket with muﬄ er and heat

shield assembly. Secure muﬄ er and heat shield

assembly with nuts.

2. Torque nuts to 8 N·m (70.8 in. lb.).

Install Air Cleaner Base, Element, and Cover
Dual-Element

1. Install air cleaner base and secure with screws.
2. Install paper element with precleaner onto air

cleaner stud and secure with washer and wing nut (if

equipped).

3. Install air cleaner cover and secure with wing nut.

Low-Proﬁ le

1. Install air cleaner base and secure with screws.
2. Install foam element (lightly oiled) into base.
3. Install cover and secure with screw.

Prepare Engine for Operation

Engine is now reassembled. Before starting or operating

engine be sure to do following:
1. Make sure all hardware is properly torqued.
2. Make sure oil drain plugs, oil ﬁ ll plugs, and Oil

Sentry

™

wire lead bullet connectors are tightened

securely.

3. Fill crankcase with correct oil. Refer to Maintenance

and Lubrication System for oil recommendations and

procedures.

Testing Engine

NOTE: Do not adjust maximum no-load high-idle engine

speed beyond 3950 RPM maximum.

It is recommended engine be operated on a test stand or

bench prior to installation on a piece of equipment.
1. Set engine up on a test stand. Check gas and oil

levels. Start engine and run for 5-10 minutes

between idle and midrange. Adjust low-speed idle

screw so low idle speed is set to 1800 RPM (± 150)

or application speciﬁ cations.

2. Adjust high-speed stop screw as necessary to

3850 + 100 RPM (typical RPM).

Содержание Courage 3000 Series
























































Результаты поиска

Содержание Courage 3000 Series

Отзывы:

Похожие инструкции для Courage 3000 Series

Бренды по названию

Популярные бренды

Kohler Courage 3000 Series, Руководство по обслуживанию

Результаты поиска

Содержание Courage 3000 Series

Отзывы:

Похожие инструкции для Courage 3000 Series

Бренды по названию

Популярные бренды