Kohler Courage 3000 Series Скачать руководство пользователя страница 47

Страница: 47 / 56

Reassembly

18 690 01 Rev. F

KohlerEngines.com

d. Hold adjuster from turning and tighten locknut.

Torque locknut to 10 N·m (88.5 in. lb.).

e. Recheck that clearance is correct.

5. Set gap of new spark plug to 0.76 mm (0.030 in.).
6. Install spark plug in cylinder head and torque to

27 N·m (20 ft. lb.).

Install Valve Cover
Valve Cover Torque Sequence

Valve Cover with Gasket

1. Make sure sealing surfaces of valve cover and

cylinder head are clean, and free of any nicks or

burrs.

2. Install a new valve cover gasket, followed by valve

cover on head with screws and torque to 8.0 N·m

(71 in. lb.) using sequence shown.

Valve Cover with RTV

RTV Sealant

NOTE: Always use fresh sealant. Using outdated

sealant can result in leakage. Refer to Tools and

Aids for important information on sealant

dispenser.

NOTE: To ensure proper adhesion of sealant to both

surfaces, perform step 3 immediately (5 minutes

maximum) after application of RTV.

1. Prepare sealing surface of cylinder head and valve

cover.

2. Apply a 1.5 mm (1/16 in.) bead of sealant to valve

cover as shown.

3. Position cover on cylinder head and start mounting

screws.

4. Torque screws to 8.0 N·m (71 in. lb.) using sequence

shown.

Содержание Courage 3000 Series
























































Результаты поиска

Содержание Courage 3000 Series

Отзывы:

Похожие инструкции для Courage 3000 Series

Бренды по названию

Популярные бренды

Kohler Courage 3000 Series, Руководство по обслуживанию

Результаты поиска

Содержание Courage 3000 Series

Отзывы:

Похожие инструкции для Courage 3000 Series

Бренды по названию

Популярные бренды