manualshive.com logo in svg

Kohler Courage 3000 Series, Руководство по обслуживанию, Страница: 43 / 56

Поделиться
Скачать
Kohler Courage 3000 Series Скачать руководство пользователя страница 43

43

Reassembly

18 690 01 Rev. F

KohlerEngines.com

NOTE:  Make sure engine is assembled using all 

specifi ed torque values, tightening sequences, 

and clearances. Failure to observe specifi cations 

could cause severe engine wear or damage. 

Always use new gaskets.

Install Crankcase Bearings and Oil Seals 

NOTE:  Oil bearings liberally with engine oil when 

installing.

NOTE:  In steps 3 and 4, position oil seals with 

manufacturer’s identifi cation marks visible and 

facing you. 

1.  Make sure there are no nicks, burrs, or damage in 

bores for bearings. Crankcase and closure plate 

must be clean.

2.  Use an arbor press to make sure bearings are 

installed straight into their respective bore, until fully 

seated.

3.  Using an appropriate seal driver, install oil seal into 

closure plate to a depth of 5.5 mm (0.217 in.) from 

outer surface.

4.  Using an appropriate seal driver, install oil seal into 

crankcase to a depth of 0.0-1.0 mm (0.0-0.039 in.) 

from outer surface.

Crankcase Components

N

S

C

B

A

D

E

F

I

K

J

L

M

G

A

T

U

O

H

P

R

Q

A

Oil Seal

B

Closure Plate Bearing

C

Closure Plate

D

Gasket

E

Camshaft

F

Crankshaft

G

Oil Sentry

™

 Float 

Switch

H

End Cap

I

Connecting Rod

J

Piston Pin Retainer

K

Piston Pin

L

Piston

M

Piston Ring Set

N

Tappet

O

Governor Cup

P

Governor Washer

Q

Governor Shaft

R

Governor Gear

S

Governor Cross Shaft

T

Crankcase Bearing

U

Dowel Pin

V

Oil Seal Depth

W

Outer Surface

A

V

W

Содержание Courage 3000 Series

























































Отзывы:

Нет отзывов