Kohler Courage 3000 Series Скачать руководство пользователя страница 45

Страница: 45 / 56

Reassembly

18 690 01 Rev. F

KohlerEngines.com

Install Closure Plate

Torque Sequence

NOTE: Make sure governor lever is against cup on

governor gear assembly.

1. Check to be sure sealing surfaces of crankcase and

closure plate are clean and free of nicks or burrs.

2. Install dowel pins and install a new closure plate

gasket (dry) onto dowel pins.

3. Install closure plate to crankcase. Carefully seat

ends of camshaft and balance shaft into their mating

bearings. Rotate crankshaft slightly to help engage

governor gear teeth.

4. Install screws securing closure plate to crankcase.

Torque screws in sequence shown to 24 N·m

(212 in. lb.).

Flywheel/Ignition Components

Flywheel Retaining

Nut

Drive Cup

Flywheel Fan

Flywheel

Flywheel Shield

Ignition Module

Install Flywheel

CAUTION

Damaging Crankshaft and Flywheel can

cause personal injury.

Using improper procedures can lead to broken

fragments. Broken fragments could be thrown from

engine. Always observe and use precautions and

procedures when installing ﬂ ywheel.

NOTE: Before installing ﬂ ywheel make sure crankshaft

taper and ﬂ ywheel hub bore are clean, dry, and

completely free of lubricants. Presence of

lubricants can cause ﬂ ywheel to be over

stressed and damaged when nut is torqued to

speciﬁ cation.

NOTE: Make sure ﬂ ywheel key is installed properly in

keyway. Flywheel can become cracked or

damaged if key is not installed properly.

1. Install woodruﬀ key into keyway of crankshaft. Be

sure that key is properly seated and parallel with

taper of shaft.

2. Install ﬂ ywheel onto crankshaft, being careful not to

shift position of woodruﬀ key.

3.  Install ﬂ ywheel shield and secure with screw.
4.  Install fan bosses into matching holes in ﬂ ywheel.
5.  Position drive cup on ﬂ ywheel, engaging boss on its

base with corresponding hole on ﬂ ywheel. Hold in

position and install nut. Finger tighten to keep cup

indexed.

6. Use a ﬂ ywheel strap wrench and torque wrench to

tighten ﬂ ywheel nut. Torque nut to 74 N·m

(655 in. lb.).

Install Ignition Module

NOTE: Ensure ignition module is correctly oriented.
1. Turn ﬂ ywheel so magnet is away from location

where ignition module will be installed.

2. Install ignition module loosely to bosses with screws.

Move module as far away from ﬂ ywheel as possible,

then tighten screws just enough to hold it in position.

3. Rotate ﬂ ywheel in a clockwise direction until magnet

is under 1 leg of ignition module.

4. Insert a 0.254 mm (0.010 in.) ﬂ at feeler gauge

between leg of module and magnet. Loosen nearest

screw, allowing magnet to draw module against

feeler gauge. Push against module to hold leg tight

against feeler gauge while tightening screw.

5. Rotate ﬂ ywheel until magnet is under other leg of

module. Loosen nearest screw, allowing magnet to

draw module against feeler gauge. Push against

module to hold leg tight against feeler gauge while

tightening screw.

6. Torque both module screws to 8 N·m (70.8 in. lb.).
7. Rotate ﬂ ywheel back and forth, checking to make

sure magnet does not strike module.

Содержание Courage 3000 Series
























































Результаты поиска

Содержание Courage 3000 Series

Отзывы:

Kohler Courage 3000 Series, Руководство по обслуживанию, Страница: 45 / 56

Результаты поиска

Содержание Courage 3000 Series

Отзывы: