manualshive.com logo in svg

Kohler Courage 3000 Series, Руководство по обслуживанию, Страница: 23 / 56

Поделиться
Скачать
Kohler Courage 3000 Series Скачать руководство пользователя страница 23

23

Fuel System

18 690 01 Rev. F

KohlerEngines.com

•  Inspect carburetor body for cracks, holes, and other 

wear or damage.

•  Inspect float for cracks, holes, and missing or 

damaged float tabs. Check float hinge and shaft for 

wear or damage.

•  Inspect fuel inlet needle and seat for wear or damage.

1.  Perform removal procedures for appropriate air 

cleaner and carburetor outlined in Disassembly. 

2.  Clean exterior surfaces of dirt or foreign material 

before disassembling carburetor. Remove bowl 

retaining screws, and carefully separate fuel bowl 

from carburetor. Do not damage fuel bowl O-rings. 

Transfer any remaining fuel into an approved 

container. Save all parts. Fuel can also be drained 

prior to bowl removal by loosening/removing bowl 

drain screw.

3.  Remove float pin and inlet needle. Seat for inlet 

needle is not serviceable and should not be 

removed.

4.  Clean carburetor bowl and inlet seat areas as 

required.

5.  Carefully remove main jet from carburetor. After 

main jet is removed, main nozzles can be removed 

through bottom of main towers. Note orientation/

direction of nozzles. End with 2 raised shoulders 

should be out/down adjacent to main jets.

6.  Save parts for cleaning and reuse unless a jet kit is 

also being installed. Clean slow jets using 

compressed air or carburetor cleaner, do not use 

wire.

NOTE: There are 2 O-rings on body of idle jet.
Carburetor is now disassembled for appropriate cleaning 

and installation of parts in overhaul kit. See instructions 

provided with repair kits for more detailed information.

High Altitude Operation

If this engine is operated at an altitude of 4000 ft. 

(1219 meters) or above, a high altitude carburetor 

kit is required. To obtain high altitude carburetor kit 

information or to fi nd a Kohler authorized dealer, visit 

KohlerEngines.com or call 1-800-544-2444 (U.S. and 

Canada).
This engine should be operated in its original 

confi guration below 4000 ft. (1219 meters).
Operating this engine with the wrong engine 

confi guration at a given altitude may increase its 

emissions, decrease fuel effi  ciency and performance, 

and result in damage to the engine.

Содержание Courage 3000 Series

























































Отзывы:

Нет отзывов