background image

19

Air Cleaner/Intake

18 690 01 Rev. F

KohlerEngines.com

AIR CLEANER

These systems are CARB/EPA certifi ed and components 

should not be altered or modifi ed in any way.

Dual-Element Air Cleaner Components

A

B

D

C

E

A

A

Wing Nut

B

Air Cleaner Cover

C

Precleaner

D

Paper Element

E

Air Cleaner Base

Low-Profi le Air Cleaner Components

I

H

G

F

F

Air Cleaner Base

G

Foam Element

H

Air Cleaner Cover

I

Screw

NOTE:  Operating engine with loose or damaged air 

cleaner components could cause premature 

wear and failure. Replace all bent or damaged 

components.

NOTE:  Paper element cannot be blown out with 

compressed air.

Dual-Element

Remove wing nut and air cleaner cover.

Precleaner

1.  Remove precleaner from paper element.
2.  Replace or wash precleaner in warm water with 

detergent. Rinse and allow to air dry.

3.  Reinstall precleaner over paper element.

Paper Element

1.  Remove wing nut (if equipped) and paper element 

with precleaner.

2.  Separate precleaner from element; service 

precleaner and replace element. 

3.  Reinstall precleaner over paper element; secure with 

wing nut (if equipped).

Reinstall air cleaner cover and secure with wing nut.

Low-Profi le

1.  Remove screw and air cleaner cover.
2.  Remove foam element from base.
3.  Wash foam element in warm water with detergent. 

Rinse and allow to air dry.

4.  Lightly oil foam element with new engine oil; 

squeeze out excess oil.

5.  Reinstall foam element into base.
6.  Reinstall cover and secure with screw.

BREATHER TUBE

Make sure both ends of breather tube are properly 

connected.

AIR COOLING

 

WARNING

Hot Parts can cause severe burns.
Do not touch engine while operating or just 

after stopping.

Never operate engine with heat shields or guards 

removed.

Proper cooling is essential. To prevent over heating, 

clean screens, cooling fi ns, and other external surfaces 

of engine. Avoid spraying water at wiring harness or any 

electrical components. Refer to Maintenance Schedule.

Содержание Courage 3000 Series

























































Отзывы: