manualshive.com logo in svg

Kohler Courage 3000 Series, Руководство по обслуживанию, Страница: 34 / 56

Поделиться
Скачать
Kohler Courage 3000 Series Скачать руководство пользователя страница 34

34

Disassembly/Inspection and Service

KohlerEngines.com

18 690 01 Rev. F

Clean all parts thoroughly as engine is disassembled. 

Only clean parts can be accurately inspected 

and gauged for wear or damage. There are many 

commercially available cleaners that will quickly remove 

grease, oil, and grime from engine parts. When such a 

cleaner is used, follow manufacturer’s instructions and 

safety precautions carefully.
Make sure all traces of cleaner are removed before 

engine is reassembled and placed into operation. Even 

small amounts of these cleaners can quickly break down 

lubricating properties of engine oil.

Disconnect Spark Plug Lead

NOTE:  Pull on boot only, to prevent damage to spark 

plug lead.

1.  Disconnect spark plug lead from spark plug.
2.  Push fuel shut-off  lever left to close fuel valve.

Drain Oil From Crankcase

1.  Remove 1 oil drain plug and 1 oil fi ll plug.
2.  Allow ample time for oil to drain from crankcase.

Remove Muffl

  er and Heat Shield Assembly

1.  Remove nuts, lock washers, and fl at washers.

2.  Remove muffl  er assembly from exhaust outlet.
3.  Remove exhaust gasket from exhaust outlet.

Remove Air Cleaner Assembly

Remove air cleaner base from engine as follows:
1.  Remove screws securing base of air cleaner 

assembly to engine.

2.  Disconnect breather hose and remove base of air 

cleaner assembly.

3.  Remove nuts and carburetor cover.
4.  Loosely install nuts on studs (to temporarily hold 

carburetor on engine).

Remove Fuel Tank

1.  Ensure fuel tank is empty.
2.  Loosen clamp and disconnect fuel line from inlet of 

shut-off  valve.

3.  Remove nuts.
4.  Remove screw and fuel tank while guiding fuel hose 

through engine bracket.

Blower Housing/Control Panel Components

G

F

L

M

E

D

A

B

J

H

C

I

K

A

Governor Lever

B

Nut

C

Governor Spring

D

Throttle Link

E

Dampening Spring

F

Control Assembly

G

Carburetor

H

Retractable Starter

I

On/Off  Wiring 

Harness Bullet 

Connector

J

Blower Housing

K

Oil Sentry

™

 Wiring 

Harness Bullet 

Connector

L

Oil Sentry

™

 Module

M

Oil Sentry

™

 Bracket

Содержание Courage 3000 Series

























































Отзывы:

Нет отзывов