Kohler Courage 3000 Series Скачать руководство пользователя страница 39

Страница: 39 / 56

Disassembly/Inspection and Service

18 690 01 Rev. F

KohlerEngines.com

Crankcase Components

Closure Plate Oil Seal

Closure Plate Bearing

Closure Plate

Gasket

Camshaft

Crankshaft

Oil Sentry

™

Float

Switch

End Cap

Connecting Rod

Piston Pin Retainer

Piston Pin

Piston

Piston Ring Set

Tappet

Governor Cup

Governor Washer

Governor Shaft

Governor Gear

Governor Cross Shaft

Crankcase Bearing

Crankcase Oil Seal

Dowel Pin

Remove Closure Plate

NOTE: Do not pry on gasket surface of crankcase or

closure plate, as this can cause damage and

leakage.

1. Remove screws securing closure plate to crankcase.
2. Remove closure plate, gasket, and dowel pins (if

required) from crankcase.

Inspection

Inspect oil seal in closure plate and remove it if it is worn

or damaged. New oil seal can be installed after closure

plate is assembled to crankcase. See Reassembly for oil

seal installation instructions.
Inspect main bearing surface for wear or damage (refer

to Speciﬁ cations). Replace closure plate if required.

Содержание Courage 3000 Series
























































Результаты поиска

Содержание Courage 3000 Series

Отзывы:

Похожие инструкции для Courage 3000 Series

Бренды по названию

Популярные бренды

Kohler Courage 3000 Series, Руководство по обслуживанию

Результаты поиска

Содержание Courage 3000 Series

Отзывы:

Похожие инструкции для Courage 3000 Series

Бренды по названию

Популярные бренды