Kohler Courage 3000 Series Скачать руководство пользователя страница 36

Страница: 36 / 56

Disassembly/Inspection and Service

KohlerEngines.com

18 690 01 Rev. F

Remove Valve Cover/Breather, Rocker Arms, Push

Rods and Cylinder Head Assembly

NOTE: Mark location of push rods and any other part

removed that will be reused.

Valve Cover with Gasket

1. Remove screws and remove valve cover and gasket

from engine. Breather assembly is inside valve

cover.

2. Remove screws securing cylinder shroud and

remove cylinder shroud.

3. Loosen and remove rocker arm lock nuts and

adjuster nuts. Remove rocker arms and push rods.

4.  Remove spark plug.
5.  Remove screws securing cylinder head.
6.  Remove cylinder head, dowel pins, and cylinder

head gasket.

Valve Cover with RTV Sealant

NOTE: Valve cover is sealed to cylinder head using

RTV silicone sealant. When removing valve

cover, use care not to damage gasket surfaces

of cover and cylinder head. To break RTV seal,

hold block of wood against 1 ﬂ at surface of valve

cover. Strike wood ﬁ rnly with mallet. If seal

doesn't break loose after 1 or 2 attempts, repeat

procedure on other side.

1. Remove screws and remove valve cover from

engine. Breather assembly is inside valve cover.

2. Using a brass wire brush and gasket remover or

similar solvent, clean old RTV from surface of

cylinder head and valve cover.

3. Remove screws securing cylinder shroud and

remove cylinder shroud.

4. Loosen and remove rocker arm lock nuts and

adjuster nuts. Remove rocker arms and push rods.

5.  Remove spark plug.
6.  Remove screws securing cylinder head.
7.  Remove cylinder head, dowel pins, and cylinder

head gasket.

Remove Valves

NOTE: Mark location of any part removed that will be

reused.

1. Supporting head of valve from below, depress valve

keeper and valve spring until keeper can be

released from valve stem. Remove valve spring and

valve from head. Repeat this procedure for

remaining valve.

2. Remove and replace intake valve stem seal

whenever cylinder head is serviced or disassembled.

Содержание Courage 3000 Series
























































Результаты поиска

Содержание Courage 3000 Series

Отзывы:

Похожие инструкции для Courage 3000 Series

Бренды по названию

Популярные бренды

Kohler Courage 3000 Series, Руководство по обслуживанию

Результаты поиска

Содержание Courage 3000 Series

Отзывы:

Похожие инструкции для Courage 3000 Series

Бренды по названию

Популярные бренды