manualshive.com logo in svg

Kohler Courage 3000 Series, Руководство по обслуживанию, Страница: 46 / 56

Поделиться
Скачать
Kohler Courage 3000 Series Скачать руководство пользователя страница 46

46

Reassembly

KohlerEngines.com

18 690 01 Rev. F

Assemble Cylinder Head

NOTE:  Engine utilizes a valve stem seal on intake 

valve. Always use a new seal when valves are 

installed in cylinder head. Never reuse an old 

seal.

1.  Install valves into their respective positions.
2.  Install a new valve seal on stem of intake valve.
3.  Install valve springs and retainers into their 

respective locations in cylinder head. Using hand 

pressure, compress each valve spring and slide 

each retainer onto valve stem to lock in place.

Install Cylinder Head

1.  Check to make sure there are no nicks or burrs on 

sealing surfaces of cylinder head or crankcase.

2.  Rotate crankshaft to position piston at TDC on 

compression stroke.

3.  Install dowel pins into recesses around lower 

cylinder head bolt holes and install a new cylinder 

head gasket.

4.  Install cylinder head and start screws. Tighten 

screws initially to a torque of 12 N·m (106 in. lb.) in 

several increments using sequence shown. Tighten 

to a fi nal torque of 24 N·m (212 in. lb.).

Install Push Rods and Rocker Arms

NOTE:  Push rods should always be installed in original 

location.

1.  Install push rod guide plate, aligning holes for rocker 

arm studs. Install rocker arm studs and torque to 

13.6 N·m (120 in. lb.). 

2.  Dip ends of push rods in engine oil and install them 

in their respective locations, seating each into tappet 

socket.

3.  Assemble rocker arms, adjusters, and locknuts onto 

rocker arm studs and push rods.

4.  Adjust valve tappet clearance as follows:
 

a.  Be sure piston is still at top of compression 

stroke.

 

b.  Insert a fl at feeler gauge between rocker arm and 

valve stem. Recommended valve to rocker arm 

clearance for intake is 0.1 mm (0.0040 in.) and 

0.15 mm (0.0060 in.) for exhaust.

 

c.  Adjust clearance as required by loosening locknut 

and tightening adjuster.

 

  Turn clockwise to decrease clearance.

 

  Turn counterclockwise to increase clearance.

Cylinder Head Components

G

H

I

L

N

A

B

C

D

E

F

K

M

O

J

1

3

4

2

A

Valve Cover

B

Adjusting Nut

C

Rocker Arm

D

Rocker Arm Stud

E

Push Rod Guide

F

Push Rod

G

Valve Keeper

H

Valve Spring

I

Intake Valve Stem 

Seal

J

Cylinder Shroud

K

Valve

L

Spark Plug

M

Dowel Pins

N

Cylinder Head

O

Torque Sequence

8.  Connect kill wire to ignition module bottom blade terminal and route wire lead across top of crankcase.

Содержание Courage 3000 Series

























































Отзывы:

Нет отзывов