- 44 -
9. Specification/External Dimension
91. Specification
Item
Type
Blow unit: DTY-WB01-□-□
Dust collecting unit: DTY-ZMW01-□-□
Input voltage
24 VDC±5%
Current consumption
Blow unit: 0.6 A Max
Dust collecting unit x1: 1.0 A Max (2.0 A Max at start-up)
Equipped ionizer
DTY-ELK01 (x1)
Ion balance *1)
±15 V (0.5 MPa, 50 mm)
Discharge time *1)
1 sec (1000 V → 100 V, 0.5 MPa, 50 mm)
Fluid used
Air (Clean air free from water and oil)
Working pressure range
0.2 to 0.7 MPa
Ionized air setting pressure range
0.05 to 0.5 MPa
Piping connection bore
φ8 quick joint
Air blow time
Rotary switch TIME 16-
point
0.5 - 10 s/continuous (sensor OFF_delay: 0.1 s - 3.0 s)
Blow intermittent frequency
Rotary switch FREQ 10-
point
1, 2, 3, 4, 6, 8, 10 Hz/continuous (no intermittent)
User setting 2 area
Switches
Locker switch
Power ON/OFF (○: OFF /
-
: ON)
Piano dip switch: SW1
Ionizer discharge time count enabled/disabled
(ON: count enabled/OFF: count disabled)
Piano dip switch: SW2
Blow valve ON/OFF cycle count enabled/disabled
(ON: count enabled/OFF: count disabled)
Indicators
POWER (green, turns on when the power is on)
ALM (red, turns on/flashes on error)
MAINT (yellow, turns on when a maintenance required)
ION BLOW (blue, turns on during blow operation)
EPS (yellow, turns on at electrostatic potential sensor judgment)
DUST (blue/green/ red, indicating the dust sensor status)
External output
Output
ALARM (Output on error)
CHECK (Ionizer discharge abnormal output)
MAINT (Maintenance timing output)
EPS (Electrostatic potential sensor judgment output)
DUST (Dust sensor judgment output)
END (Blow operation end output)
VAC START (External device operation output)
Input
STOP (Operation stop input)
Start (Operation start input)
ZC (Electrostatic potential sensor zero calibration input)
Connectability sensor
Photoelectronic sensor: DTY-ZSP□L-WB
Electrostatic potential sensor: DTY-EPS01-EA-□LWB
Dust sensor
(Dust collecting unit: built into DTY-ZMW01-□-DS)
Nozzle
Shower type: 60°, 90°, flat (three types)
Pinpoint
type: φ2, φ3, φ4 (three types)
Consumed air flow rate *2)
Air blow side
330 L/min (ANR)
Ionized air side
170 L/min (ANR)
Dust collecting fan exhaust flow rate
2000 L/min at no load
Filter collection capability *3)
OUT side
62%
Communication
RS485 communication
Number of communication connections
15
Operating environment
Indoor 0 - 40°C, 15 -65% RH (no condensation)
Weight
Blow unit: 2.1 kg (no photoelectronic sensor/power unit)
Dust collecting unit: 1.3 kg (with a dust sensor)
Mount
4 L-shaped brackets (screws) enclosed with each unit
Box type
A4 type
DTY-WBM01-S-□-□
Weight: 7.5 Kg
(with a nozzle and a dust sensor/without a power unit)
A3 type
DTY-WBM01-L-□-□
Weight: 9.5 Kg
(with a nozzle and a dust sensor/without a power unit)
*1) The values are based on Koganei’s measurement criteria They are not guaranteed values.
*2) Nozzle: Pinpoint φ2 x 2, with the conditions of a nozzle shower 60°/slop valve fully open/supply pressure 0.7 MPa/ionized air regulator
setting pressure 0.5 MPa
*3) Test method: ASHRAE 52.1-1992 (weighing method) test dust: ASHRAE TEST DUST
*4) Value of the dust sensor is just a guide. It does not guarantee removal of dust from the workpiece.
Содержание ION WIPER DTY-WB01
