manualshive.com logo in svg

Knick SensoGate WA 133 Series, Руководство пользователя

Поделиться
Скачать
Knick SensoGate WA 133 Series Скачать руководство пользователя страница 27

27

1.  Move the drive unit to PROCESS position until 

the two screws 

(Z)

 become visible.  

Loosen the two screws 

(Z)

 using a screwdriver 

(TX 25) until they contact the stop at the 

immersion tube (see illustration).

Note:

 Contrary to the figure, the O-ring may still be in the immersion tube.

Immersion Tube

SensoGate WA 133

Z

T

D

2.  Turn the immersion tube 

(T)

 counterclockwise 

by approx. 60°.

3.  The bayonet coupling opens so you can pull 

out the immersion tube 

(T)

 in direction of the 

arrow.

4.  Now, the O-ring 

(D)

 (sensor gasket) is visible. 

Check and replace if required  

(O-ring dimensions: 11.9 x 2.6 mm).

Conditions: 

First, separate the immersion tube from the process adaptation (see “Removing the Drive Unit” 

chapter).

Stop for the  

screws on the 

immersion tube

Removing the Immersion Tube

Содержание SensoGate WA 133 Series













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды