manualshive.com logo in svg

Knick SensoGate WA 133 Series, Руководство пользователя

Поделиться
Скачать
Knick SensoGate WA 133 Series Скачать руководство пользователя страница 18

E

F

18

Sensors with Solid Electrolyte

SensoGate WA 133

Short Immersion Depth

A

J

C

D

E

G

Mounting wrench, 

ZU 0647

Installing the Sensor

Before installing the sensor, make sure that the 

retractable fitting is in 

SERVICE position

.

1.  Use appropriate sensors 

(A)

 only: 

Diameter: 12 mm Length: 225 mm 

Observe the pressure resistance of the sensor.

2.  Make sure that the slide washer 

(C)

 and the 

O-ring 

(D)

 are correctly positioned and not 

damaged.

3.  Insert the sensor and screw in the sensor head 

(J)

 (19 mm A/F, PG 13.5 thread) with a max. 

torque of 3 Nm (recommended tool: 19 mm 

mounting wrench, e.g., Knick ZU 0647).  

Note: 

When tightening the sensor, you must 

overcome the elastic force of the internal 

 sensor  monitoring.

4.  Connect the cable jack 

(G)

.  

Hold the cable in a loop and fix it using clamp 

(E)

.

  

Note: 

The cable loop must be long enough 

so that the cable does not impede the stroke 

movement of the retractable fitting.

5.  Connect the equipotential bonding cable to 

terminal 

(F)

 (if required).

6.  Mount the protective cap (ZU 0759) if required 

(see user manual of protective cap).

Содержание SensoGate WA 133 Series













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды