Knick MemoTrans Скачать руководство пользователя | Manualshive

Страница: 41 / 56

background image

MemoTrans

41

No. Message

S

1)

D

2)

F

3)

Sensor type Configurable Tests or remedial action

241 Firmware error

F

On

On

All

No

Software error - internal

1. Carry out software update.

2. Replace backplane.

3. Please contact the Service Department

and quote the number shown.

243 Firmware error

F

On

On

All

No

Software error - internal

1. Carry out software update.

2. Replace backplane.

3. Please contact the Service Department

and quote the number shown.

284 Firmware update

F

On

On

All

No

Firmware update active, please wait.

285 Update error

F

On

On

All

No

Firmware update failed. Possible reasons:
Read error, SD card is faulty, incorrect
firmware on SD card.

1. Check device settings.

2. Check electronics module type.

373 Temperature of elec-

tronics is high

M

On

Off

All

No

Temperature of backplane electronics is
high.

• Check ambient temperature and

energy consumption.

384 Firmware error

F

On

On

All

No

Sensor measuring sequence counter.
No measurement signal from sensor.

1. Update software.

2. Contact the Service Department.

408 Calibration aborted

M

Off

Off

P, C, O,

No

Calibration aborted.

411 Upload/download

active, please wait

C

On

Off

All

No

Up-/Download active,

• please wait.

460 Output undershot

S

On

Off

All

No

Current output undershot.
Measured value out of specified current
range.
Possible reasons: Sensor / sample line in
air, air pockets in the fitting, incorrect
flow to sensor, sensor / sample line is
contaminated.

1. Check sensor.

2. Check application.

3. Clean sensor / sample line.

461 Output overshot

S

On

Off

All

No

Current output overshot. Measured value
out of specified current range.
Possible reasons: Sensor / sample line in
air, air pockets in the fitting, incorrect
flow to sensor, sensor / sample line is
contaminated.

1. Check sensor.

2. Check application.

3. Clean sensor / sample line.

1)

Status signal factory setting

2)

Diagnostics message factory setting

3)

Fault current factory setting

«
...
39
40
41
42
43
...
»

Содержание MemoTrans

























































Отзывы:

Нет отзывов

Похожие инструкции для MemoTrans

Бренд: Nautel Страницы: 4

Бренд: IBR Страницы: 20

Бренд: GE Страницы: 40

Бренд: Spotwave Страницы: 2

Бренд: SILENTSYSTEM Страницы: 9

Бренд: SPC Страницы: 28

Бренд: Labom Страницы: 24

Бренд: Rane Страницы: 2

Бренд: Atel Страницы: 9

Gewa Control Easy HM

Бренд: Abilia Страницы: 12

Бренд: SSD Страницы: 30

Бренд: AUDIOropa Страницы: 88

Бренд: QRP Labs Страницы: 66

Бренд: Aerial-51 Страницы: 3

Бренд: Williams Sound Страницы: 8

Бренд: Kyosho Страницы: 6

Бренд: GE Страницы: 4

Бренд: GE Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды