Knick MemoTrans Скачать руководство пользователя

Страница: 51 / 56

MemoTrans

Nominal Operating Conditions

Ambient temperature

–20

…

85 °C / -4

…

185 °F

Transport / storage
temperature

-40

…

85 °C / -40

…

185 °F

Process temperature

Fitting in measuring position:
T(process) = max. 100 °C / 212 °F, continuous operation
T(ambient) = max. 60 °C / 140 °F, continuous operation

Fitting in service position
T(process) = max. 145 °C / 293 °F, continuous operation
T(ambient) = max. 60 °C / 140 °F, continuous operation

Relative humidity

…

95 % not condensing

Max. altitude above MSL

< 2000 m / < 6562 ft.

Output

…

20 mA current loop floating, protected against inverse polarity

Linearization/transmission
behavior

Linear

Supply voltage

12.6

…

30 V DC (with a fault current > 20 mA)

…

30 V DC (with a fault current < 4 mA)

Surge protection

IEC 61 000-4-4 and IEC 61 000-4-5, ± 1 kV each

Signal on alarm

3.6

…

23 mA

Connection

2-wire cable
4

…

20 mA positive: blue

…

20 mA negative: white

Housing

PEEK, color: light gray, RAL 7035

Memosens closure

PEEK, color: black

Cable

TPE, color: black, Ø approx. 5 mm

Optical waveguide

PC; color: transparent

Cable length

3 m / 10 ft; 7 m / 23 ft; 15 m / 49 ft

Impact loads

The product is designed for mechanical impact loads of 1 J (IK06) as per the
requirements of EN 61010-1.

Dimensions

See dimension drawing

Protection

IP67, IP68, NEMA 6

Weight

MemoTrans:
with 3 m / 10 ft cable approx. 190 g / 7 oz
with 7 m / 23 ft cable approx. 380 g / 13 oz
with 15 m / 49 ft cable approx. 760 g / 27 oz

Connections

Terminals, conductor cross-section max. 2.5 mm

Simulation

Specific parameters can be simulated for test purposes:
Current, measured value, or temperature

Содержание MemoTrans

























































Результаты поиска

Содержание MemoTrans

Отзывы:

Похожие инструкции для MemoTrans

Бренды по названию

Популярные бренды

Knick MemoTrans, Руководство пользователя

Результаты поиска

Содержание MemoTrans

Отзывы:

Похожие инструкции для MemoTrans

Бренды по названию

Популярные бренды