Knick MemoTrans Скачать руководство пользователя | Manualshive

Страница: 26 / 56

background image

MemoTrans

26

11 Diagnostics and Troubleshooting

11.1 Diagnostic Information via LED

See LED display in the Commissioning chapter.

LED Display, p. 14

11.2 Adapting the Diagnostic Information

Path:

Diagnostics



Diagnostic settings

Function

Options

Info

Sensor change alarm
delay

0

…

180 s

Factory setting

30 s

Sensor HOLD

Fault current

3.6

…

23.0 mA

Factory setting

3.6 s

Possible range of fault current.

LED shows NAMUR
status signal

Selection

• Off

• On

Factory setting

Off

Additional LED signals for diagnostic messages as per NAMUR NE107
categories.

Diagnostics behavior

The list of diagnostic messages displayed. There are device-specific
messages, and messages that depend on what sensor is connected.
Select the message to be adapted.
Only then can you make the settings for this message.

Status signal

The messages are divided into different error categories in accordance
with NAMUR NE107.

Diagnostics behavior

Selection

• Service

• Alarm

LED as per NAMUR NE107 categories:

Three rapid green blinks at the start of the message means: Everything OK – but pay attention!

The more red blinks there are at the end of a message, the more critical the diagnostics as per NE107.
Continuous red-only blinking means: Error in device or sensor, take action immediately.

LED behavior

Status

Three rapid green blinks and a single rapid red blink Device or sensor requires maintenance.

M status signal as per NAMUR NE107

Three rapid green blinks and two rapid red blinks

Device and sensor are being operated out of specification.

S status as per NAMUR NE107

Three rapid green blinks and three rapid red blinks

Device or sensor undergoing function check.

C status signal as per NAMUR NE107

Red

Blinks quickly

Failure of device or sensor

F status signal as per NAMUR NE107

«
...
24
25
26
27
28
...
»

Содержание MemoTrans

























































Отзывы:

Нет отзывов

Похожие инструкции для MemoTrans

TRANSDUCER MOUNTING PROCEDURE - SCHEMA REV B

Бренд: Simrad Страницы: 1

Бренд: Icom Страницы: 116

AIR-EAGLE FM2 43-1000-SSB-R1/8-DC

Бренд: BWI Eagle Страницы: 2

FT DX 9000 - CAT OPERATION REFERENCE BOOK

Бренд: Yaesu Страницы: 20

Бренд: Landmark Страницы: 2

Easywave RTM08 Series

Бренд: Eldat Страницы: 2

Бренд: M-system Страницы: 7

Бренд: Icom Страницы: 3

Бренд: AFi Страницы: 8

Бренд: Icom Страницы: 88

Clearview 4:2 12

Бренд: Blonder tongue Страницы: 8

Бренд: SHITEK Страницы: 2

Бренд: Kenwood Страницы: 14

Бренд: Kenwood Страницы: 24

Бренд: Kenwood Страницы: 18

Бренд: Kenwood Страницы: 23

Бренд: Kenwood Страницы: 40

Бренд: Kenwood Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды