KitchenAid KSSC36FKB00 Скачать руководство пользователя страница 31

Страница: 31 / 76

4-5

To remove a door switch (Revised De-
sign):

a) Remove the two hex-head screws from

the door switch cover and remove the
cover.

Door Switch Cover Screws

b) Disconnect the wire connectors from

the door switch terminals.

c) Press in on the locking arms and push

the switch out of the bracket.

Door Switch

To remove the power switch:

a) Remove the unit compartment front

cover, pull the cover forward, and turn
it over (see step 5 on page 4-2 for the
procedure).

b) Remove the four wire connectors from

the power switch terminals.

c) Press in on the locking arms and push

the switch out of the cover opening.

Power Switch

Locking
Arms

To remove the inverter assembly:

a) Remove the two hex-head screws from

the air diverter and remove the diverter.

b) Remove the three remaining hex-head

screws from the front guard and re-
move the guard.

Screw

Air
Diverter

Front
Guard

c) Remove the hex-head screw from the

front of the inverter assembly.

Screw

Inverter

Assembly

Retaining Bracket

Continued on the next page.

Содержание KSSC36FKB00













































































Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды

KitchenAid KSSC36FKB00, Техническое образование

Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды