KitchenAid KSSC36FKB00 Скачать руководство пользователя страница 30

Страница: 30 / 76

4-4

REMOVING A DOOR SWITCH, THE POWER SWITCH,

THE INVERTER ASSEMBLY, AND

THE MAIN CONTROL BOARD ASSEMBLY

NOTE:

Sharp edges may be present.

Unplug the refrigerator or disconnect the
power.

Remove the main and louvered decora-
tive panels (see page 4-2).

Electrical Shock Hazard

Disconnect power before servicing.
Replace all panels before operating.
Failure to do so can result in death or
electrical shock.

Hex-Head Bolts

Bracket

b) Remove the two hex-head screws from

the door switch cover and remove the
cover.

Door Switch Cover Screw (1 of 2)

c) Disconnect the wire connectors from

the door switch terminals.

d) Press in on the locking arms and push

the switch out of the bracket.

Wire Connectors

Locking Arm

Door Switch

To remove a door switch (Original De-
sign):

a) Remove the two hex-head bolts from

the door switch bracket and turn the
bracket over.

Power Switch

Main Control Board Assembly

Inverter Assembly

Содержание KSSC36FKB00













































































Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды

KitchenAid KSSC36FKB00, Техническое образование

Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды