KitchenAid KSSC36FKB00 Скачать руководство пользователя страница 50

Страница: 50 / 76

4-24

c) Disconnect the three wire connectors

and remove the subpanel.

b) Remove the two hex-head screws from

the switch subpanel, pull the panel for-
ward, and turn it over.

Hex-Head Screws

2 Wire Connectors

Wire Connector

c) Repeat the previous step for the other

corner of the front panel.

d) Pull the bottom of the front panel out

and then down to remove it from the
dispenser.

To remove the dispenser:

a) Disconnect the front panel wire con-

nector and remove the panel.

REASSEMBLY NOTE: To reinstall the front
panel on stainless steel trimless doors:

Fit the top edge of the panel into the door
opening.

Place a folded towel over the top edge of
the panel and hit it with the rubber mallet
you used earlier to seat it in the door.

Place the folded towel along the bottom
edge of the front panel and seat it with the
mallet.

Seat This Area Last

Seat This Area First

Содержание KSSC36FKB00













































































Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды

KitchenAid KSSC36FKB00, Техническое образование

Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды