KitchenAid KSSC36FKB00 Скачать руководство пользователя страница 55

Страница: 55 / 76

5-1

COMPONENT TESTING

Before testing any of the components, perform
the following checks:

• The most common cause for control failure is

corrosion on connectors. Therefore, discon-
necting and reconnecting wires will be nec-
essary throughout test procedures.

Refer to page 4-18 for the procedure for servic-
ing a thermistor.

Run the diagnostics tests (see page 6-1)
and test the thermistors in steps 01 and
02.

NOTE: For accurate temperature/resistance
readings, continue with the remaining steps to
check the resistance of the thermistor(s).

Unplug the refrigerator or disconnect the
power.

Disconnect the thermistor wire connector
from the main harness.

Set the ohmmeter to the R x 1K scale.

Insert the test probes into the two connec-
tor pins of the thermistor connector.

THERMISTOR

NOTE: If the resistance of the thermistor(s)
was normal, perform the following voltage test.

Set the voltmeter to read a maximum
voltage of 10 volts DC.

Connect power to the refrigerator and
allow it to enter the “cooling” mode.

With the thermistor disconnected and the
refrigerator in the cooling mode, touch the
voltmeter test probes to the thermistor
main harness connector pins. The meter
should indicate approximately 5 volts DC.

If the voltage was not present, check for a
thermistor output at the main control board
(see page 5-5).

Depending on the temperature, the meter
should indicate within the approximate
range, as shown in the chart below.

• Check all connections before replacing com-

ponents, looking for broken or loose wires,
failed terminals, or wires not pressed into
connectors far enough.

• Resistance checks must be made with power

cord unplugged from outlet, and with wiring
harness or connectors disconnected.

Electrical Shock Hazard

Disconnect power before servicing.
Replace all panels before operating.
Failure to do so can result in death or electrical shock.

TEMPERATURE

RESISTANCE

TEMPERATURE

RESISTANCE

(

°°°°

OHMS (APPROX.)

(

°°°°

OHMS (APPROX.)

–5

25900-27500

4 5

5930-6300

22100-23500

5190-5510

18900-20000

4550-4830

16200-17200

4 0 0 0 - 4 2 4 0

13900-14800

3520-3730

12000-12800

3100-3300

10400-11000

2740-2910

8990-9550

2430-2580

8750

2160-2290

7800-8290

1920-2030

4 0

6800-7220

Содержание KSSC36FKB00













































































Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды

KitchenAid KSSC36FKB00, Техническое образование

Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды