KitchenAid KSSC36FKB00 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 76

background image

4-18

REMOVING A THERMISTOR

NOTE:

Sharp edges may be present.

1.

Unplug the refrigerator or disconnect the
power.

NOTE: The refrigerator and freezer thermistors
are identical and are removed in the same
manner.

2.

Depending  on  the  thermistor,  open  the
freezer or refrigerator door, and remove
any  items from the shelf that are in front of
the  thermistor.  It  may  be  necessary  to
remove the shelf as well. The thermistor
locations are shown below.

Electrical Shock Hazard

Disconnect power before servicing.
Replace all panels before operating.
Failure to do so can result in death or
electrical shock.

4.

Disconnect the 2-wire connector and re-
move the thermistor.

3.

Remove the hex-head screw from the
thermistor cover. Pull the cover forward at
the screw end, and unhook the tab from
the slot at the other end of the thermistor
cover.

Refrigerator / Freezer

Thermistor Cover

Screw

Connector

Refrigerator / Freezer

Thermistor

Freezer Thermistor

Refrigerator Thermistor

«
...
42
43
44
45
46
...
»

Содержание KSSC36FKB00













































































Отзывы:

Нет отзывов

Похожие инструкции для KSSC36FKB00

Бренд: Samsung Страницы: 111

Бренд: Samsung Страницы: 60

Бренд: Wagan Страницы: 7

Бренд: NEFF Страницы: 24

Бренд: Haier Страницы: 36

Бренд: Danby Страницы: 42

Бренд: Jenn-Air Страницы: 44

Бренд: Hamilton Beach Страницы: 22

Бренд: Oypla Страницы: 7

Бренд: Thetford Страницы: 7

Бренд: Omcan Страницы: 16

Бренд: Daewoo Страницы: 29

Бренд: ROMMER Страницы: 14

Бренд: Linea 2000 Страницы: 76

Бренд: Dometic Страницы: 124

Бренд: Jocel Страницы: 80

Бренд: Kenmore Страницы: 48

Бренд: Atag Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды