KitchenAid KSSC36FKB00 Скачать руководство пользователя страница 48

Страница: 48 / 76

4-22

REMOVING THE WATER VALVE

Electrical Shock Hazard

Disconnect power before servicing.
Replace all panels before operating.
Failure to do so can result in death or
electrical shock.

Disconnect the 1/2

″

nut from the water

valve inlet.

Remove the two hex-head mounting
screws from the water valve mounting
bracket.

NOTE:

Sharp edges may be present.

Unplug the refrigerator or disconnect the
power.

Remove the two screws from the base
grille and remove the grille.

Turn off the water supply to the refrigera-
tor.

Base Grille

Screw

NOTE: The water valve location is shown be-
low.

Water Valve

Position a container to catch the water in
the next step.

Pull the water valve forward and discon-
nect the water outlet tubing nut(s).

Disconnect the solenoid connector(s)
from the water valve terminal(s).

Water Valve

Inlet Tubing

Water Valve

Bracket Screws

Solenoid Connectors

Water Outlet Tubing Nuts

Содержание KSSC36FKB00













































































Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды

KitchenAid KSSC36FKB00, Техническое образование

Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды