KitchenAid KSSC36FKB00 Скачать руководство пользователя страница 47

Страница: 47 / 76

4-21

Pull Tubing Up Through Grommet

Use a putty knife, slide the retainer clips off
the door channel, and pull the water line
out from under the channel.

Door Channel

Clip

Reach under the front of the refrigerator
and remove the water reservoir outlet tub-
ing nut from the water valve and remove
the nut from the end of the tubing.

Position a container to catch the water in
the next step.

Disconnect the nut from the union and
remove the nut from the end of the water
reservoir tubing.

Union Nut

Unhook the front edge of the drip pan and
pull it out the front of the refrigerator.

Unhook Front

10. Remove the crisper and bottom shelves

from the refrigerator compartment.

11. Remove the hex-head screw from the

water reservoir tubing strap.

12. Pull the ends of the water reservoir tubing

up through the grommet.

Drip Pan

Water Reservoir Tubing Nut

Water Reservoir Tubing Strap

Содержание KSSC36FKB00













































































Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды

KitchenAid KSSC36FKB00, Техническое образование

Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды