KitchenAid KSSC36FKB00 Скачать руководство пользователя страница 43

Страница: 43 / 76

4-17

To remove the auger motor or crush/
cube solenoid:

a) Remove the light shield and the bulb

from the socket.

b) Remove the four hex-head screws from

the auger assembly and pull the as-
sembly forward.

Light Shield & Bulb

Auger Assembly

c) Disconnect the electrical harness con-

nector, and remove the auger assem-
bly.

Screws

Harness Connector

d) To remove the auger, unscrew the drive

coupler (left-hand threads) and remove
it from the motor shaft.

e) Remove the three auger motor hex-

head screws from the housing.

Drive Coupler

Remove

f) Disconnect the wires from the auger

motor terminals.

g) Disconnect the wires from the solenoid

terminals.

h) Remove the green ground wire from

the ground terminal.

i) To remove the crush/cube solenoid,

remove the two hex-head mounting
screws from the housing (see above).

Auger Motor Wires

Solenoid Screws

Solenoid Wires

Auger Motor
Screw (2 of 3)

Ground Wire

Содержание KSSC36FKB00













































































Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды

KitchenAid KSSC36FKB00, Техническое образование

Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды