KitchenAid KSSC36FKB00 Скачать руководство пользователя страница 36

Страница: 36 / 76

4-10

Lift and unhook the two evaporator cover
tabs, then lower the cover until the top
edge clears the air duct, and slide the
cover up and out of the freezer.

REMOVING THE BIMETAL, THE EVAPORATOR FAN

MOTOR, THE DEFROST HEATER, AND THE EVAPORATOR

NOTE:

Sharp edges may be present.

Unplug the refrigerator or disconnect the
power.

Open the freezer door.

Remove the freezer shelves that are over
the evaporator cover.

Remove the indicated two shelf mounting
studs.

Evaporator

Cover

Shelf Studs

Remove the eight hex-head screws from
the evaporator cover.

Screws

(2 of 8)

Unhook Evaporator

Cover Tabs

To remove the bimetal:

a) Unclip the bimetal from the evaporator

inlet tubing.

b) Follow the instructions that were sup-

plied with the replacement bimetal to
connect the wires.

Bimetal

Electrical Shock Hazard

Disconnect power before servicing.
Replace all panels before operating.
Failure to do so can result in death or
electrical shock.

Clip

Содержание KSSC36FKB00













































































Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды

KitchenAid KSSC36FKB00, Техническое образование

Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды