KitchenAid KSSC36FKB00 Скачать руководство пользователя страница 64

Страница: 64 / 76

6-2

WATER FILTER INPUT (WFI) TEST

To confirm that the water valves are being
monitored by the WFI control, follow the pro-
cedures listed:

Testing The Dispenser Valve Input

1. Open the refrigerator door.

2. Depress the refrigerator light switch.

3. Place a container under the water spout.

4. Activate the water dispenser.

5. Read the WFI display. “00” indicates a

normal input.

Testing The Ice maker Valve Input

1. Open the refrigerator door.

2. Depress the refrigerator light switch.

3. Activate the ice maker and wait for a water

fill.

4. Read the WFI display during the fill. “99”

indicates a normal input.

DIAGNOSTICS CHART

Step

Component Tested

Result*

Comment

Thermistor is within normal range.

Thermistor is open or less than –20

Thermistor is shorted or greater than 115

Thermistor is within normal range.

Thermistor is open or less than 10

Thermistor is shorted or greater than 115

Evaporator Fan Motor is On at correct speed.

Evaporator Fan Motor is On at incorrect speed.

0 4

Condenser Fan Motor

Condenser Fan Motor is On.

Compressor is On at 4500 rpm.

Compressor is Off waiting for minimum (7 minute) Off delay.

Air Door

Air Door fully opens. **

Defrost Heater is energized, bimetal closed.

Bimetal open.

†

FreezerThermistor

Refrigerator Thermistor

†

The bimetal may be bypassed with an insulated jumper.

Compressor

** The air door will close at step 01, and reset to the correct opening after exiting diagnostics.

Press the “Water Filter Reset” to exit diagnostics.
* Shown on the Water Filter Indicator display.

Bimetal/Defrost Heater

Evaporator Fan Motor

Содержание KSSC36FKB00













































































Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды

KitchenAid KSSC36FKB00, Техническое образование

Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды