KitchenAid KSSC36FKB00 Скачать руководство пользователя страница 34

Страница: 34 / 76

4-8

REMOVING THE CONDENSER FAN MOTOR

NOTE:

Sharp edges may be present.

Unplug the refrigerator or disconnect the
power.

Remove the main and louvered decora-
tive panels (see page 4-2).

Remove the unit compartment cover (see
pages 4-2 & 4-3 for the procedures).

Electrical Shock Hazard

Disconnect power before servicing.
Replace all panels before operating.
Failure to do so can result in death or
electrical shock.

Remove the two hex-head screws from
the condenser fan motor and remove the
motor from the bracket.

Condenser Fan Motor

Viewed From Back Of Unit

Wire

Connector

Remove the two hex-head screws from
the fan motor bracket (see the photo at the
top of the next column).

Disconnect the wire connector from the
condenser fan motor.

Fan Motor Bracket Screws

Lay the condenser fan motor on a work
surface with the fan blade facing up.

Remove the speed nut from the condenser
fan blade and remove the blade from the
motor shaft. NOTE: Be sure to position the
fan blade with the “Nut Side” facing as
shown when you reinstall it later.

Nut Side

Speed Nut

Motor Screws

Содержание KSSC36FKB00













































































Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды

KitchenAid KSSC36FKB00, Техническое образование

Результаты поиска

Содержание KSSC36FKB00

Отзывы:

Похожие инструкции для KSSC36FKB00

Бренды по названию

Популярные бренды