KitchenAid KBFC42FS Скачать руководство пользователя страница 53

Страница: 53 / 76

4-31

REMOVING THE WATER FILTER HOUSING

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

WARNING

5. Remove the water valve (see page 4-30

for the procedure).

6. Remove the two hex-head screws from

the front of the water filter mounting
bracket.

1. Unplug refrigerator or disconnect power.
2. Turn off the water supply to the refrigera-

tor.

3. Remove the water filter from the bottom

of the refrigerator.

4. Remove the two screws from the base

grille and remove the grille from the bot-
tom of the refrigerator.

Screw

Water Filter

Base Grille

Water Inlet Tube

Filter Housing

Water Filter Mounting Bracket

7. Pull the water filter housing forward as

far as it will go, then disconnect the water
inlet tube from the filter housing, and re-
move the housing from the refrigerator.

Содержание KBFC42FS













































































Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды

KitchenAid KBFC42FS, Техническое образование

Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды