KitchenAid KBFC42FS Скачать руководство пользователя страница 26

Страница: 26 / 76

4-4

REMOVING THE USER INTERFACE ASSEMBLY

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

1. Unplug refrigerator or disconnect power.
2. If needed, remove the food and racks from

the upper shelf.

3. Place the fingers of both hands into the

light cover slots and pull the cover down.

WARNING

4. Remove the six hex-head screws from

the user interface frame and remove the
frame.

5. Pull the user interface assembly forward

and remove it from the five retainer clips.

User Interface Frame

Screws (3 of 6)

Light Cover Slots

6. Unlock and disconnect the user interface

connector from the wiring harness.

User Interface Clips

User Interface

Connector

Содержание KBFC42FS













































































Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды

KitchenAid KBFC42FS, Техническое образование

Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды