KitchenAid KBFC42FS Скачать руководство пользователя страница 74

Страница: 74 / 76

8-2

ADJUSTING THE FREEZER DOOR

4 Alignment Holes

(Right Side)

2.  Pull the freezer drawer out.
3.  Remove the food from the drawer.
4.  Lift the liner out of the freezer drawer.
5.  Remove the bottom T-15 screw from both

sides of the the freezer drawer front.

6. Close the freezer drawer and adjust the

door front so that it is properly aligned and
the gasket seats evenly against the cabinet.

NOTE:

The cabinet trims may need to be

removed to view the door seal.

7. Without moving the freezer drawer front,

slowly open the freezer drawer, and locate
one of the holes in the left and right four
hole groupings that are properly aligned.

8. Install the two screws you removed in step

5, in the left and right aligned holes, and
tighten them securely.

9. Close the freezer drawer, and make sure

that the gasket seats securely against the
cabinet.

Keep Edges

Parallel

Alignment

Holes

Freezer

Door

Bottom Screw

Freezer Door

Gasket

1. Unplug refrigerator or disconnect power.

NOTE:

This adjustment allows you to level

the freezer door with the cabinet surface to
prevent leakage and frost from occurring.

Содержание KBFC42FS













































































Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды

KitchenAid KBFC42FS, Техническое образование

Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды