KitchenAid KBFC42FS Скачать руководство пользователя страница 37

Страница: 37 / 76

4-15

To remove the condenser fan motor:

a) Remove the hex-head screws from the

fan motor bracket (see the top right
photo).

d) Disconnect the 3-pin connector from

the compressor pins.

e) Disconnect the ground wire from the

compressor terminal.

f) Remove the screw from the chassis

ground wire and remove the inverter.

Ground

Wire

3-Pin

Connector

Ground

Wire &

Screw

b) Press down on the locking tabs and pull

the wire connector off the fan motor.

c) Remove the speed nut from the blade

and remove the blade from the motor
shaft.

Condenser Fan Motor

Bracket Screws

Connector

Speed Nut

d) Remove the two hex-head screws

from the fan motor and remove the
motor from the bracket.

Motor Screws

Continued on the next page.

Содержание KBFC42FS













































































Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды

KitchenAid KBFC42FS, Техническое образование

Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды