KitchenAid KBFC42FS Скачать руководство пользователя страница 29

Страница: 29 / 76

4-7

REMOVING A REFRIGERATOR TEMP-CONTROLLED

MOTORIZED AIR DOOR

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

1. Unplug refrigerator or disconnect power.
2. Remove the temp-controlled drawer for

the motorized air door you are removing.

WARNING

6. Peel off the adhesive covering from over

the motorized air door, and remove the
air door.

5. Disconnect the motorized air door wire

connector from the wire harness, and re-
move the air door.

3. Remove the two hex-head screws from

the motorized air door cover.

4. Pull the motorized air door assembly for-

ward and turn it over.

Temp-Controlled Motorized Air Doors

Air Door Cover Screws

Motorized Air Door Connector

Adhesive Covering

Содержание KBFC42FS













































































Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды

KitchenAid KBFC42FS, Техническое образование

Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды