KitchenAid KBFC42FS Скачать руководство пользователя страница 48

Страница: 48 / 76

4-26

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

4. Remove the three hex-head screws from

the evaporator fan motor cover and re-
move the cover.

WARNING

REMOVING THE EVAPORATOR FAN MOTOR

7. Pull forward on the evaporator fan motor,

disengage the blade from the motor shaft,
and remove the motor.

NOTE:

When you

reinstall the fan blade on the motor shaft,
make sure you push it on all the way, and
that it spins freely. Keep all wiring away
from the blade.

1. Unplug refrigerator or disconnect power.
2. Remove the freezer drawer (see page

4-20 for the procedure).

3. Remove the storage drawer from the

freezer.

Freezer Storage Drawer

5. Unlock and disconnect the evaporator

fan motor connector from the wire har-
ness.

NOTE:

Do not allow the wire har-

ness to fall behind the evaporator cover,
otherwise you will have to remove the
cover to retrieve it.

6. Squeeze the top and bottom of the evap-

orator fan motor bracket and remove it
from the motor.

Evaporator Fan Motor Cover

Evaporator Fan Motor Connector

Bracket

Fan Motor

Blade

Содержание KBFC42FS













































































Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды

KitchenAid KBFC42FS, Техническое образование

Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды