KitchenAid KBFC42FS Скачать руководство пользователя страница 28

Страница: 28 / 76

4-6

REMOVING THE REFRIGERATOR

MOTORIZED AIR DOOR

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

1. Unplug refrigerator or disconnect power.
2. If needed, remove the food and racks

from the upper shelf.

WARNING

5. Unlock and disconnect the motorized air

door connector from the wiring harness
and remove the air door and cover.

6. Peel off the adhesive covering from over

the motorized air door, and remove the
air door from the cover.

Motorized Air Door

3. Remove the three hex-head screws from

the motorized air door cover.

4. Pull down on the motorized air door cover

to unhook it from the rear clips and turn it
over.

Motorized Air Door Cover Screws

Motorized Air

Door Connector

Adhesive Covering

Refrigerator

Motorized Air Door

Содержание KBFC42FS













































































Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды

KitchenAid KBFC42FS, Техническое образование

Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды