KitchenAid KBFC42FS Скачать руководство пользователя страница 52

Страница: 52 / 76

4-30

REMOVING THE WATER VALVE

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

1. Unplug refrigerator or disconnect power.
2. Turn off the water supply to the refrigera-

tor.

3. Remove the water filter from the bottom

of the refrigerator.

4. Remove the two screws from the base

grille and remove the grille from the bot-
tom of the refrigerator.

WARNING

5. Push in on the quick-disconnect ring and

pull the water line off the water valve inlet
(see the top right photo).

6. Remove the two hex-head screws from

the water valve mounting bracket, and pull
the bracket forward as far as possible.

Screw

Water Filter

Base Grille

7. Disconnect the wire connector from the

water valve terminals.

8. Push in on the quick-disconnect ring and

pull the water line off the water valve out-
let.

9. Remove the two hex-head screws from

the water valve and remove the valve
from the mounting bracket.

Screws

Water Valve Inlet Line

Quick-Disconnect Ring

Filter Housing

Water Valve Outlet Line

Quick-Disconnect Ring

Valve Terminal Connector

Screw

Water Valve

Содержание KBFC42FS













































































Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды

KitchenAid KBFC42FS, Техническое образование

Результаты поиска

Содержание KBFC42FS

Отзывы:

Похожие инструкции для KBFC42FS

Бренды по названию

Популярные бренды