KitchenAid KBFC42FS Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 76

background image

5-4

Refer to page 4-12 for the procedure for ac-
cessing the condenser fan motor.
1. Run the diagnostics tests (see page 6-2)

and check for the proper operation of the
condenser fan motor in step 04.

NOTE:

During the condenser fan motor op-

eration, 120 volts AC will be present at pins
1 and 4.

CONDENSER FAN MOTOR

1 2 3 4

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.

WARNING

EVAPORATOR FAN MOTOR

Refer to page 4-26 for the procedure for ac-
cessing the evaporator fan motor.
1. Run the diagnostics tests (see page 6-2)

and check for the proper operation of the
evaporator fan motor in step 03.

NOTE:

During the evaporator fan motor op-

eration, 5 to 17 volts DC will be present at the
yellow and white wires. A constant 12 volts at
the red and white wires will be present any-
time the fan motor is operating. The remaining
steps will allow you to check the resistance of
the evaporator fan motor.
2. Unplug refrigerator or disconnect power.
3. Disconnect the wire connector going to

the evaporator fan motor.

4. Set the ohmmeter to the R x 10K scale.
5. Touch the ohmmeter test leads to pins 1

(white wire) and 4 (red wire) of the evap-
orator fan motor connector. The meter
should indicate approximately 1400 to
1700

Ω

.

1 2
3 4

«
...
56
57
58
59
60
...
»

Содержание KBFC42FS













































































Отзывы:

Нет отзывов

Похожие инструкции для KBFC42FS

Бренд: Gamko Страницы: 88

Бренд: Samsung Страницы: 2

Бренд: Aegis Страницы: 24

Бренд: Kirkland Signature Страницы: 16

CombiCooler V6000 Supreme

Бренд: V-ZUG Страницы: 22

Бренд: Avanti Страницы: 16

Бренд: Hotpoint Страницы: 16

FX Series FX2-4N1WS

Бренд: Randell Страницы: 2

Бренд: Blomberg Страницы: 48

Бренд: U-Line Страницы: 30

Бренд: Tricity Bendix Страницы: 20

Бренд: MicroFridge Страницы: 2

Бренд: THOR Страницы: 10

GTS12BBPALCC and

Бренд: GE Страницы: 20

Бренд: Concept2 Страницы: 17

Бренд: Tesla Страницы: 46

Бренд: Miele Страницы: 48

KFN 14927 SD ed

Бренд: Miele Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды