manualshive.com logo in svg

Kia Sportage 2008, Руководство пользователя, Страница: 76 / 227

Поделиться
Скачать
Kia Sportage 2008 Скачать руководство пользователя страница 76

7/6/12

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

76/227

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

(2) Measure resistance between the terminal 1 of PAB harness connector and the terminal 22 of SRSCM harness

connector.

specification(resistance) : below 1 Ω

(3) Is the measured resistance within specification?

►

Check short circuit.

►

Repair or replace the wiring harness between the PAB and the SRSCM.

4. CHECK SHORT CIRCUIT

(1) Measure resistance between the terminal 1 and 2 of PAB harness connector.

specification(resistance) : infinite

(2) Is the measured resistance within specification?

►

 Go to next step.

►

 Repair or replace the wiring harness between the PAB and the SRSCM.

5. CLEAR THE DTC AND CHECK THE VEHICLE AGAIN

(1) Install the DAB module and connect the DAB connector.

(2) Connect the connectors of the PAB, SAB, CAB, BPT, FIS and SIS.

(3) Connect the SRSCM connector.

(4) Connect the negative (­) terminal to the battery.

(5) Connect a Hi­Scan(Pro) to the data link connector.

(6) Turn the ignition switch to ON.

(7) Clear the DTC stored in the SRSCM memory with the Hi­Scan(Pro).

(8) Turn the ignition switch to LOCK and wait for at least 30 seconds.

(9) Turn the ignition switch to ON and wait for at least 30 seconds.

(10) Check the vehicle again with the Hi­Scan(Pro).

Does the above DTC(s) go off?

►

 Problem is intermittent or was repaired and SRSCM memory was not cleared.

►

Replace the SRSCM with a new one, and then check the vehicle again. At this time, if the vehicle normally

operates with a new SRSCM, the fault may be the SRSCM(Replace SRSCM).

Restraint > Troubleshooting > B1354

DTC Description

The Passenger Airbag circuit consists of the SRSCM and the Passenger Airbag (PAB) which has two squib circuits.
The SRSCM sets above DTC(s) if it detects short to ground on the PAB circuit.

DTC Detecting Condition

DTC

Condition

Probable cause

B1354

• Short to ground between PAB module and SRSCM

• Short to ground on wiring

harness

Содержание Sportage 2008




































































































































































































































Отзывы:

Нет отзывов