manualshive.com logo in svg

Kia Sportage 2008, Руководство пользователя, Страница: 183 / 227

Поделиться
Скачать
Kia Sportage 2008 Скачать руководство пользователя страница 183

7/6/12

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

183/227

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

(3) Is the measured resistance within specification?

►

Check the DAB Module.

►

 Repair or replace the wiring harness between the DAB and the clockspring or between the clockspring and the

SRSCM.

3. CHECK THE DAB MODULE

(1) Replace the Driver Airbag(DAB) with a new one.

● Refer to "Driver Airbag(DAB)" section in this SERVICE MANUAL.

(2) Install the DAB module and connect the DAB connector.

(3) Connect the connectors of the PAB, SAB, CAB, BPT, BUPT, FIS and SIS.

(4) Connect the SRSCM connector.

(5) Connect the negative (­) terminal to the battery.

(6) Connect a Hi­Scan(Pro) to the data link connector.

(7) Turn the ignition switch to ON and check the vehicle again.

Does Hi­Scan (Pro) indicate any DTC related to DAB?

►

Check the clockspring.

►

Replace the Driver Airbag(DAB).

4. CHECK THE CLOCKSPRING

(1) Check the clockspring. Is the clockspring normal?

►

 Go to next step.

►

 Replace the clockspring.

5. CLEAR THE DTC AND CHECK THE VEHICLE AGAIN

(1) Install the DAB module and connect the DAB connector.

(2) Connect the connectors of the PAB, SAB, CAB, BPT, BUPT, FIS and SIS.

(3) Connect the SRSCM connector.

(4) Connect the negative (­) terminal to the battery.

(5) Connect a Hi­Scan(Pro) to the data link connector.

(6) Turn the ignition switch to ON

(7) Clear the DTC stored in the SRSCM memory with the Hi­Scan(Pro).

(8) Turn the ignition switch to LOCK and wait for at least 30 seconds.

(9) Turn the ignition switch to ON and wait for at least 30 seconds.

(10) Check the vehicle again with the Hi­Scan(Pro).

Does the above DTC(s) go off?

Содержание Sportage 2008




































































































































































































































Отзывы:

Нет отзывов