manualshive.com logo in svg

Kia Sportage 2008, Руководство пользователя, Страница: 52 / 227

Поделиться
Скачать
Kia Sportage 2008 Скачать руководство пользователя страница 52

7/6/12

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

52/227

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

(7) Turn the ignition switch to ON and check the vehicle again.

Does Hi­Scan (Pro) indicate any DTC related to FIS?

►

 Go to next step.

►

 Replace the Front Impact Sensor(FIS).

4. CLEAR THE DTC AND CHECK THE VEHICLE AGAIN

(1) Clear the DTC stored in the SRSCM memory with the Hi­Scan(Pro).

(2) Turn the ignition switch to LOCK and wait for at least 30 seconds.

(3) Turn the ignition switch to ON and wait for at least 30 seconds.

(4) Check the vehicle again with the Hi­Scan(Pro).

Does the above DTC(s) go off?

►

 Problem is intermittent or was repaired and SRSCM memory was not cleared.

►

Replace the SRSCM with a new one, and then check the vehicle again. At this time, if the vehicle normally

operates with a new SRSCM, the fault may be the SRSCM(Replace SRSCM).

Restraint > Troubleshooting > B1330

DTC Description

The detecting system for front crash consists of the SRSCM and two Front Impact Sensors (FIS).

Inspection Procedure

If above DTC is detected , replace two Front Impact Sensors(FIS).

Restraint > Troubleshooting > B1331

DTC Description

The detecting system for front crash consists of the SRSCM and two Front Impact Sensors (FIS). The SRSCM sets
above DTC(s) if it detects that any FIS is defective or there is communication error between any FIS and the SRSCM.

DTC Detecting Condition

DTC

Condition

Probable cause

B1326
B1331

• Short to ground between FIS and SRSCM
• Front Impact Sensor(FIS) Malfunction
• SRSCM Malfunction

• Short to ground on

Wiring Harness

• Front Impact

Sensor(FIS) squib

• SRSCM

Schematic Diagram

Содержание Sportage 2008




































































































































































































































Отзывы:

Нет отзывов