manualshive.com logo in svg

Kia Sportage 2008, Руководство пользователя, Страница: 217 / 227

Поделиться
Скачать
Kia Sportage 2008 Скачать руководство пользователя страница 217

7/6/12

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

217/227

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

Schematic Diagram

Terminal & Connector Inspection

1. Visually inspect all connectors related to the affected circuit for damage and secure connection.

2. Inspect terminals for damage and corrosion.

Avoid damaging connectors during the inspection process.

3. Are any problems found?

►

 Go to next step.

►

 After repairing the trouble part, check whether DTC occurs or not.

Inspection Procedure

1. PREPARATION

(1) Turn the ignition switch to LOCK.

(2) Disconnect the negative (­) terminal from the battery and wait for at least 3 minutes.

(3) Remove the DAB module and disconnect the DAB connector.

(4) Disconnect the connectors of the PAB, SAB, CAB, BPT, BUPT, FIS and SIS.

(5) Disconnect the SRSCM connector.

2. CHECK OPEN CIRCUIT

(1) Measure resistance between the terminal 7 of BPT harness connector and the terminal 34(31) of SRSCM

harness connector.

(2) Measure resistance between the terminal 2 of BPT harness connector and the terminal 33(32) of SRSCM

harness connector.

specification(resistance) : below 1 Ω

(3) Is the measured resistance within specification?

►

 Check short to ground.

►

 Repair the open circuit on wiring harness between the BS and the SRSCM.

3. CHECK SHORT TO GROUND

(1) Measure resistance between the terminal 7 of BS harness connector and chassis ground.

specification(resistance) : infinite

(2) Is the measured resistance within specification?

►

 Check the BS.

►

 Repair or replace the wiring harness between the BS and the SRSCM.

4. CHECK THE SEAT BELT BUCKLE SWITCH (BS)

(1) Measure current between the terminal 7 of BS and 34(31) of SRSCM.

Содержание Sportage 2008




































































































































































































































Отзывы:

Нет отзывов