manualshive.com logo in svg

Kia Sportage 2008, Руководство пользователя, Страница: 54 / 227

Поделиться
Скачать
Kia Sportage 2008 Скачать руководство пользователя страница 54

7/6/12

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

54/227

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

(2) Is the measured resistance within specification?

►

Check Front Impact Sensor.

►

 Repair or replace the wiring harness between the FIS and the SRSCM.

3. CHECK FRONT IMPACT SENSOR

(1) Replace the front impact sensor(FIS) with a new one.

● Refer to "Front Impact Sensor(FIS)" section in this SERVICE MANUAL.

(2) Install the DAB module and connect the DAB connector.

(3) Connect the connectors of the PAB, SAB, CAB, BPT, BUPT, FIS and SIS.

(4) Connect the SRSCM connector.

(5) Connect the negative (­) terminal to the battery.

(6) Connect a Hi­Scan(Pro) to the data link connector.

(7) Turn the ignition switch to ON and check the vehicle again.

Does Hi­Scan (Pro) indicate any DTC related to FIS?

►

 Go to next step.

►

 Replace the Front Impact Sensor(FIS).

4. CHECK THE DTC AGAIN

(1) Turn the ignition switch to LOCK and wait for at least 30 seconds.

Check again that the battery negative (­) terminal is disconnected from the battery.

(2) Install the DAB module and connect the DAB connector.

(3) Connect the connectors of the PAB,SAB,CAB,BPT,BUPT,FIS and SIS.

(4) Connect the SRSCM connector.

(5) Connect the negative (­) terminal to the battery.

(6) Connect a Hi­Scan(Pro) to the data link connector.

(7) Turn the ignition switch to ON and check the vehicle again.

Does Hi­Scan (Pro) indicate any DTC?

►

 Problem is intermittent or was repaired and SRSCM memory was not cleared.

►

Replace the SRSCM with a new one, and then check the vehicle again. At this time, if the vehicle normally

operates with a new SRSCM, the fault may be the SRSCM(Replace SRSCM).

Restraint > Troubleshooting > B1332

DTC Description

Содержание Sportage 2008




































































































































































































































Отзывы:

Нет отзывов