Kia Sportage 2008 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 227

Kia Sportage 2008 Скачать руководство пользователя страница 32

7/6/12

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

32/227

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

3. Remove the crash pad. (Refer to BD group crash pad)

4. Remove the mounting nuts (A) from the crash pad, then remove the passenger's airbag (B).

5. Installation is the reverse of removal.

After installing the clock spring, confirm proper system operation; Turn the ignition switch ON: the SRS
indicator light should be turned on for about 6 seconds and then go off.

INSTALLATION

1. Disconnect the negative () cable from battery and wait for at least three minutes.

2. Remove ignition key from the vehicle.

3. Place a Passenger Airbag (PAB) on the instrument panel and tighten the Passenger Airbag (PAB) mounting nuts.

Tightening Torque
: 18.6 ~ 26.5 N·m(13.7 ~ 19.5 lb·ft)

4. Install the instrument panel (Refer to BD group in this Service Manual).

5. Connect the Passenger Airbag (PAB) connectors, then install the center facia panel.

«
...
30
31
32
33
34
...
»

Содержание Sportage 2008




































































































































































































































Отзывы:

Нет отзывов