manualshive.com logo in svg

Kia Sportage 2008, Руководство пользователя, Страница: 150 / 227

Поделиться
Скачать
Kia Sportage 2008 Скачать руководство пользователя страница 150

7/6/12

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

150/227

https://www.kiatechinfo.com/viewer/toc_print.asp?vehicletype=Passenger&mfrcode=KM&area=KM…

4. CLEAR THE DTC AND CHECK THE VEHICLE AGAIN

(1) Install the DAB module and connect the DAB connector.

(2) Connect the connectors of the PAB, SAB, CAB, BPT, BUPT, FIS and SIS.

(3) Connect the SRSCM connector.

(4) Connect the negative (­) terminal to the battery.

(5) Connect a Hi­Scan(Pro) to the data link connector.

(6) Turn the ignition switch to ON .

(7) Clear the DTC stored in the SRSCM memory with the Hi­Scan(Pro).

(8) Turn the ignition switch to LOCK and wait for at least 30 seconds.

(9) Turn the ignition switch to ON and wait for at least 30 seconds.

(10) Check the vehicle again with the Hi­Scan(Pro).

Does the above DTC(s) go off?

►

 Problem is intermittent or was repaired and SRSCM memory was not cleared.

►

Replace the SRSCM with a new one, and then check the vehicle again. At this time, if the vehicle normally

operates with a new SRSCM, the fault may be the SRSCM(Replace SRSCM).

Restraint > Troubleshooting > B1410

DTC Description

The detecting system for side crash consists of the SRSCM and two Side Impact Sensors (SIS). The SRSCM sets
above DTC(s) if it detects that any SIS is defective or there is communication error between any front SIS and the
SRSCM.

DTC Detecting Condition

DTC

Condition

Probable cause

B1400
B1403
B1409
B1410

• Open between SIS and SRSCM
• Side Impact Sensor (SIS) Malfunction
• SRSCM Malfunction

• Wiring Harness
• Side Impact Sensor

(SIS) squib

• SRSCM

Schematic Diagram

Содержание Sportage 2008




































































































































































































































Отзывы:

Нет отзывов