Kentec Electronics DNX-R-2F-K Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 42

Kentec Electronics DNX-R-2F-K Скачать руководство пользователя страница 6

Functional description

The DNX R-2F/FC are network nodes that support intelligent infrastructure monitoring
of the hybrid and Optic Fibre network bus with RS-485 / ARCNET CIE interface ports
A1 and A2.

Figure 2: Design Structure Diagram

The DNX R-2F/FC can function in one of two modes:

1)

Mode 1 as a PASSIVE dual port Optic Fibre / RS-485 medium converter.

2)

Mode 2 as an ACTIVE network node in either a class A or class B monitored
network. (ACTIVE mode is required for use as a network analysis tool)

The mode can be selected through Set 6, switch 4 in Figure 6 and Table 10.

Note* The DNX R-2F/FC will operate in a basic mode unless upgraded to unlock
the additional features offered by the firmware upgrade (DNX R-2F/FC-UG).

Refer to Table 9a for the features included in the DNX R-2F/FC and DNX R-2F/FC-
UG products.

The DNX R-2F/FC may be purchased and later upgraded with the
DNX R-2F/FC-UG functionality by purchasing a license key that allows the IVIEW
application tool to unlock the additional functionality. The DNX R-2F/FC will
operate in BOTH PASSIVE and ACTIVE Modes, with the DNX R-2F/FC-UG
increasing the features set.

6

Man-1492

DNX-R-2F/FC-K

«
...
4
5
6
7
8
...
»

Содержание DNX-R-2F-K











































Отзывы:

Нет отзывов